![]() ![]() It uses the /proc/i8k interface provided by the i8k driver (an alias for dell_smm_hwmon). I8kutils is a daemon to configure fan speed according to CPU temperatures on some Dell Inspiron and Latitude laptops. It can be installed as nbfc-linux AUR or nbfc-linux-git AUR. It does not depend on the Mono framework. NBFC-Linux is a lightweight implementation of NBFC, written in C. More information about configuration is available at upstream wiki. For example, on Asus Zenbook UX430UQ, the configuration Asus Zenbook UX430UA did not work well (fans completelly stopped all the time), but Asus Zenbook UX410UQ worked fantastically. If there are no recommended models, go to NBFC git repository or /opt/nbfc/Configs/ and check if there are any similar models available from the same manufacturer. If above solution did not help, try appending ec_sys.write_support=1 to kernel parameters. # mv /opt/nbfc/Plugins/ /opt/nbfc/Plugins/.old Note: If you are getting File Descriptor does not support writing, delete and restart rvice: After that, run the following to check if it detected the sensors correctly:Ĭore 0: +29.0☌ (high = +76.0☌, crit = +100.0☌) This will detect all of the sensors present and they will be used for fancontrol. Check the official lm-sensors devices table to see if experimental drivers are available for such motherboards. Support for newer motherboards may not yet be in the Linux kernel. fw-ectool-git AUR - Fan configuration for Framework Laptops.įancontrol is a part of lm_sensors, which can be used to control the speed of CPU/case fans.ISW-Modern - Fan control application for MSI laptops.fan2go-git AUR - An alternative to Fancontrol independent of device-paths.ASUS laptops - Configure some ASUS laptops for Fancontrol or manual control.Lenovo Legion Linux - Fan speed configuration and other settings for some Lenovo Legion laptops.ThinkPad laptops - Fan configuration for some ThinkPad laptops. ![]() Dell laptops - Alternative fan control daemon for some Dell laptops.Most suitable for latest, unsupported by Fancontrol laptops. NoteBook Fan Control (NBFC) - Cross-platform solution for laptop fan control, written in C# and works under Mono runtime.Most suitable for desktops and laptops, where fan controls are available via sysfs(5). Fancontrol (lm-sensors) - Script (written in Bash) to configure fan speeds.There are multiple working solutions for fan control for both desktops and notebooks. Here is some more information about this topic. In some cases, you will not be able to use the Fancontrol script due to incompatible cooling architecture (e.g. Some laptops have two fans for CPU and GPU, but the first fan cools down CPU and GPU at the same time, while the other one cools CPU only. Some laptops have single fan for both CPU and GPU and cools both at the same time. However, if I want to set a limit for how much W in total it can use, it also makes me set the GPU and memory clock values, which will them be fixed: so at idle the GPU will use about 60 W of power.Note: Laptop users should be aware about how cooling system works in their hardware. > You see, by default the card controls its own GPU and memory clock values, which means that when idle the GPU draws around 40 W of power. Sadly, it doesn't seem to work all that well for my use case, which I mentioned in my blog post when using Linux instead of Windows as my daily driver at home too. On Linux, the best I found was CoreCtrl: With AMD Software on Windows, it's no big deal. I just wish we had an equivalent of AMD Software on Linux, so I could mess around with the settings more.įor example, I like to limit the GPU to 50-75% of it's total power for ambient heat/cooling reasons, or UPS/PSU/electricity bill reasons when specific games make it hard to cap framerates. The AMD experience on Linux is vastly better than the Nvidia one. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |